hopeSun 系列 100KTL 组串式光伏逆变器 快速安装指南.pdf

禾望电气 Hopewind
hopeSun系列 100KTL负极
2.确定输入电缆的极性后，将每一路输入电缆正、负极与组串 组串式光伏逆变器式逆变器输入端子PV、PV-一对应连接.

正极接PV， 快速安装指南负极接 PV-.
线缆选择 名称位号检参电位规格备注 注意1-~20- .由于产品开级成其他职因，本手期内容会不定期更新，限事另有的定，本手研仅作为便螺钉抱杆式安装
使用3PCSM8螺钉（题机附件）将挂件固定在安装位交流输出电缆N芯户外线境（ALB.C）A、B、C、4芯户外线强（AB.CN）或3交流输出只有1个仞水锁头，规格为32mm-38mm. 置：导线截面权推荐位（饲线始）：输出为中接线准子 价摄灯 聚缺少任付物们诚存在任何损环，省取点经销商.

2)将逆变器轻轻的由上至下挂在挂板上，检查两侧，确保RS485 通信电 X3-P235mm"推荐花用专用通讯电，或损AS485通信电缆只有一个缺时请用套筒校力.

固定在正确的位置上，使用4PCSM8螺钉（随机附件）X3-P3规格 本按席本手厨及用户于册的要求存储、拥运、安装和使用从两侧紧固连接挂板及逆变器：PE接地电缆[pe拉荐世用至少1极横截面机为无18mm-25mm.
16mm²的接地专用电缆 1.产品简介直流输入端子选择 逆变器正面逆变器有两个直流输入开关（DCSWITCH），输入路数与接入端
子的选择推荐见下表.

（1）上门板输入路数逆变春直流输入增子 (2)散热风扇PV1、 PV2 PV1. PV2. PV3 (3) 下PV1 PV3. PV4
PV1 ~ PV4. PVS 端口说明PV1 - PV6. PV7 PV1 PV7、 PV8
19PV1 PV8. PV9 PV1 - PV9PV10 螺钉挂架式安装20PV1 - PV19、 PV20 1)使用4PCSM8螺钉（随机附件）将挂件固定在安装位RS485通信线缆接线 置：在RS485转接板X1上，两个RS485接口（标记为P2、P3）， 2)将逆变器轻轻的由上至下挂在挂板上，检查两侧，确保如图所示.

处于串联中的组串式逆变器，此接口用于连接临近组 固定在正确的位置上，使用4PCSM8螺钉（随机附件）串式逆变器- 从两侧紧固连接挂板及逆变器： (1)直说开关 DC SWITCH(2) PV独线准子(1~ 20) (3) PV-核线编干(1- ~ 20- （4）交藏输出编子防水锁头 (5) WI-F/GPRS 通信接口(6)RS485 输出烯子防水膜头 逆变器及挂板安装孔位尺寸 800m
1.将过线孔的保护膜取出，将RS485线缆穿过防水锁头，与 避免逆变器受到阳光直射、雨淋与积雪，可是长使用寿命.

建议选RS485转接板X3上的接口连接.

择带遮挡的安装地点，若无法满足，请搭建遮阳棚（选配件）.

2.多台逆变器的连接建议采用下图所示方式串联.

逆变器也可通过挂板安装在承重墙壁上，请客户根据现场安装环境、 墙壁承重等因素，自行购买MB膨胀钉在堵壁打孔安装.

4.电气连接 危险 2.安装要求及工具准备在接我前，请定成以下准各工作，以免造成人身合法.

接规时，禁止带电接作，并逾守《组申式绝变用户手期》中的相关要求.

本手册仅作安装指导，详尽安装要求请参考用户手册.

1)断开逆变器直流开关，确保逆变添处于天机状志，并贴好警示标识.

2）确比输入电缓的正，次现，并微好标识，确回验入类与元优指市的性挂新开.

485接口 安装空间3)确认光伏组申的开路电压没有超过规定限值.

485接口
4确认对应的究流汇流箱新降器处于浙开状态，在连接输入线类时，确保输入电线的正、负核与组申式运变器PV编子正、负板对应.

运变器 输出侧电缆接线5.安装后检查 1.地线连接：地线接线处位于壳体外部，贴有PE标识.

地线1.确认逆变器已经可靠安装到位 线缆线径不小于16mm².

螺栓规格为M6.注意：必须保证2.检查地线是否正确连接，连接是否可靠牢固，确保无斯路、 接地线缆与接地排可靠连接.

2.交流输出电缆连接：3.检查输出线境是否正确连接，连接是否可靠牢固，确保无断路 300mm1)将逆变器底部的"ACOUTPUT"防水锁头上的锁紧帽拧短路 工具准备下:4.检查直流输入线境连接极性是否正确，连接是否可靠牢国，项
2)将交流线缆依次穿入锁紧帽和逆变器底部“AC保无新路、规路 工具成设备4内六角技手用途美变播下门板拆装备注OUTPUT防水锁头，依次连接至交流接线端子排的5.检查RS485通信线潢连接是否正确且可靠牢固口 轻开/紧因输出确子档板的A B.C.N上，紧因力矩为8N*m.7.检查莲变器下门版是否装回，门板螺钉是否紧固6.检查莲变器成部已使用的族头是否涂上防火泥□ 十字怒栓J(PH2)邮栓规格：ME和IMBPV输入电缆接线 管型编子压线时压核通信践颜璃子8.检查不需要使用的直流输入端子是否已经密封 套简报手输出电预的连胶部栓规格：MB1.压接MC4端子：9.检查直流开关DC SWITCH是否处于闭合状态 MC4第子压线钳压接 MC4冶子输入电缆需委压接成MC4润子，1)确认输入电缆的正、负极，并已做好标识.

连接.才能与道变添上的PVPV-准子2)使用剥线错剥线： MC4药除工具 万用表时安全测量电区，确保接线、安装正极
负极剥线长度要求 3.逆变器安装3)按照正确的极性，将电缆与对应线芯压接到一起.

逆变器的包装中附带有挂板，安装时需先安装挂板，再将逆变器 挂放并紧固在挂板上.

可根据实际安装环境需要，选择抱柱/抱杆 式安装、挂架式安装两种安装方式.

喉箍抱杆式安装 在挂板背侧使用至少2PCS喉箍穿过箍带安装孔（喉 客户自备）：将挂板放置到安装位置，扎紧箍带： 将逆变器轻轻的由上至下挂在挂板上，检查两侧，确保负餐 固定在正确的位置上，使用4PCSM8螺钉（随机附件）（p按照正确的极性，将线芯插入MC4连接器的公头和母 从两侧紧固连接挂板及逆变器：头，并拧紧连接器后盖.

地址：深圳官南山区西厨官龙第二工业区11栋用有深圳市系望电气股份有限公司 版本：V1.0电话：0755-8602 6786
禾望电气Hoop Mounting Insert the core into the male and female ends of the MC4 connectorandSghtenthe connectrbackcveraccoringto pumadoH1）Use at least 2 PCS hose clamps through the strap mounting thecoectpoly
(spnssholeon the back sideofthehangingplate hopeSun Series2)Hang the inverter onthe hanging plate and fasten the 100KTLhangingplateandinveterrbthsidesusingthe4PCS M8 screws (with optional accessories);:2.After detemining the polaily of the input cableconnect the String TypePVInverter QuickInstallationGuide electrode is connected to PV and the negative electrode is
connected to PV. Cable Selection AUTION Name Label Remended Cable Note The conterts of tis manual are sutject to imegular updates due fo product upgrades or other reasons. Unless othenwise agreedthis manual is only used as guidance. AI entsinformation and nemendations in the document do not constitule any) iput cable express or implied warranty. In any caseguidance in this manual cannot replace safety wamings and instrutions and PV- banch. on user manuals and product fuselage. AC oupu A. B. C、 outdoor TheACouphsny1 Aoprainseqpeb ad byprfensOp shoulid be tuly famillar with the positionworking principes and standands of the Screw Rod Mounting Remended cross whole PV system. Bek1)Use 3 PCS MB screws (with accessories) tofix the pendant sectinalarea f conductr he body has obvious external damage according to fhe packing lis". If there are any in themouting posiion AS485 X3-P2 missing itms ray damele contact hedisrbo2)Hang the inverter on the mounting plate and fasten the hangingplateandinverterfrboth sides using the4PCS X3-P3 Remove the amper-eviden label;:Thnddb Eg dfne
egound 1.Product Introductiond16 Inverter front DC Input Terminal Selection
The inverter has two DC input saitches (DC SWITCH). The number of the table below. input circuits and the selection of access teminals are remended in (1) Upper door(2) Radiator fansNumber of input channels nal ot inverter (3) Lower doorPV1、 PV2
PV1、 PV2. PV3 PV1 ~ PV3. PV4 Port description pV1 -PV4. PVS PV1 ~ PV5. PVS
Bracket Mounting PV1 ~PV6.PV7 )Use 4 PCS MB screws (supplied accessories) to fasten the PV1 ~ PV7、PV8 pVI -PV8. PVg 2)Hang the ivrler on the hanging plateand fasten the PV1 ~ PV9. PV10 using MB screws (suppled accessories); connection pegboard and the inverter from both sides by20[PV1 PV19. PV20
RS485Communication Cable Connection On the RS485 adapter board X1two RS485 interfaces (labeled P2P3) are shown. A cllection and dstributin biner box in seriesthis interlace is used to connecl adjacent collection and distribution (1) DC SWITCH(2) PV terminals (1 20)biner boxes. (3)PV- teminals (1- ~ 20-)(S)W-FIGPRS mmuricaion(4) AC otptmnl wepo kDE
(6) RS485 ouput emina arpriok Inverterand hanging plate sze 899mm3160Avoid dret sunight rain and snw s that th service e f t
junction box can be prolonged. It is remended to choose shelerdllntfle up a sun shatding shelter. This way of installation can installthe inverter on the load-bearing walls or supors youwant tinstalthe wall ustomersshoud1.Take out the protective film of the wire hole and cone nect the factors such as the instalation enironment and loadbearing on buyMexansionnalstinstahlesnthewalaordingtothe interlace on the RS485 adapler board X1. RS485cablethroughthewaterproof lockheadtoconnect wihthe the wall.2.The connection of muliple inveters is suggested o be conr
in series in the following diagram. 4.Electrical Connections 2.InstallationRequirementsand ToolsPreparation2iverterFollow 日ThismaualisfrnstalltiongudncenlyPleae cause bodily injury. Before connecting the cableplease plete the follow n to the usermanual for detailed installation requirements.5DCiih Installtion Space
dlisconnection. Data collector NF im te s4ries imyerar.5.Post-installationCheck Output side cable connection Coha etr selyistadine□ 1.2Checkth groundweis prerlyonnctdwh
open-circuit or short-circut connection is rellable and secureand ensure that there is no 300mmgrounding bar.3. Check that the output cable is properly connectedthat the Topreparation Remarks2.DC oufput cable connection: connection is reliable and secureand that there is no open-circuit or hexagon Lwerdorplale)lock at the botlom af theirverter. Screwoltelockingcap ontheACOUTPUTwaterproof short-circuit. spaner2)The AC cables are connected to A. BC and N of the AC4.CheckwheththDCinputcalecectiolartycwhether the connection is reliable and secureand ensure that there screws peoqfad pue Bolt speifications: M6 and M teminal row in tumand the fastening torque is BN*m. is n peniuit or shrt-ccu. Tuetypg SCrewS Tube type crimping plers PV Input Cable Connection5. Checkthe RS485 municion cableconnection is orrect Qudput cable connestion1.Chmp MC4 terminal: and reliable. Chcktljintshmrd
1)cable and mark them. Confim the positive and negative terminals of the input with fireproof mud n MC4 crimping plers Crimp he MC4 teminals 2)Stripping with a wire stre:7. Check i the inverter's lower door panel is replaced and the door MC4 ne val tol penel screws are tightened. Measureoletensure positive9. Check I DC SWITCH is dosed8CheckthCinput tminaltharent needed are sealed wtng andin negafive uwanbeu Stripping engh Satety equipment for constructiot ulating shoesglovest3)Press the cable together with the corresponding core
according to thecorrect polarty. 3.Inverter Installation Therenkahhnlin thehaninglatemtistallfindththeiverhod hung and fastened on the hanging plate.According to the actual installanrenstynland selectednamely the column/pole mount and wall mout.
Tel. 0755-8602 G786 OA